Ham Radio Foxhunting Overview
Updated: Jul 23
Foxhunting, what is it?
Foxhunting, also known as Radio Direction Finding (RDF), is one of the most enjoyable and challenging activities in amateur radio. Participants use their radios and directional antennas to locate hidden transmitters, affectionately known as foxes.
The foxes are concealed throughout a city, neighborhood, or local park, and hunters rely on signal strength, directional antennas, and triangulation techniques to track them down.
Example of a MicroFox 50 fox transmitter. It can be programmed using a USB cable connected to a PC to transmit a message on a VHF frequency (Example: 147.520 MHz). Fox transmitters typically transmit a message on low power (=< 1 watt) every minute. This is necessary so that the fox can be located. Some ham radio enthusiasts build their own fox transmitters using a Raspberry Pi, a circuit board, a low cost transmitter (usually a walkie talkie) and software to execute the transmission of the "fox" message. Some of the messages are rather comical. For example, a fellow ham (W1MJ) built a fox and in one of the messages you can hear his dog Noah barking in the background.
Before the event begins, the primary fox frequency is announced. At the designated start time, the fox becomes active, transmitting a repeating beacon—typically every 30 to 60 seconds. Hunters use each transmission to determine the direction of the signal and gradually narrow down the fox's location. In some events, finding one "fox" provides clues or frequencies that lead participants to additional hidden transmitters.
Fox Hunting is more than just a friendly competition. It develops practical skills that are valuable for search and rescue operations, emergency communications, interference hunting, and antenna experimentation. Most importantly, it's a fun way to improve your operating skills, meet fellow amateur radio operators, and enjoy the outdoors.
Foxhunting, tricks of the trade:
There are many tools that ham radio foxhunters use to locate the fox during the hunt. The more common methods are body deflection and using a directional antenna called a Yagi. The body deflection method involves holding a walkie talkie on the same frequency as the fox close to your body while turning 360 degrees when the fox transmits. The goal is to locate where the signal is strongest on your walkie talkie’s s-meter. The signal strength can be deceptive since radio waves bounce off hills, large trees, and other natural and manmade obstacles. Other tricks of the trade include removing the antenna when you are close and the signal is very strong. Another useful tool is tunning a second walkie talkie to the third harmonics of the fox transmitter frequency. Example: If the “fox” is transmitting on a frequency of 145.540 MHz, take the frequency and multiply it * 3 = 442.620 MHz. This method works well when you are almost on top of the transmitter. You will hear a loud squawking noise. In addition to these techniques, you can use a device called an offset attenuator. The offset attenuator and the step attenuator are outlined below. An attenuator is a helpful tool in the arsenal of foxhunting equipment; however, in the end, it comes down to good old fashion detective work, instinct, and an abundance of patience.
BIONICS offset attenuator & passive step attenuators:
The AA1 is an active offset attenuator that creates a controlled image of a transmitter's signal on a different frequency. By mixing the incoming signal with an internally generated offset frequency, it produces a duplicate ("image") that appears at a new frequency while leaving the original signal unchanged. The strength of the image can be adjusted over a wide range, allowing a very strong transmitter to be reduced to a level suitable for practice. This enables fox hunters to simulate searching for a distant or weaker transmitter without physically moving the fox or changing its output power.

The passive step attenuators feature four independently selectable attenuation stages of 5 dB, 10 dB, 20 dB, and 30 dB. These stages can be combined in any configuration to provide attenuation levels from 0 dB to 65 dB in 5 dB increments.
A passive step attenuator is one of the most useful tools a fox hunter can carry. As you get closer to the hidden transmitter, the received signal can become so strong that your radio's S-meter stays pegged, and your directional antenna no longer provides a clear indication of the transmitter's direction. An attenuator reduces the signal reaching the receiver, allowing you to continue taking accurate bearings.

In summary: a passive attenuator helps you finish the hunt by controlling an overwhelming signal as you close in on the fox; an active offset attenuator helps you create and control the hunt by generating a realistic, adjustable signal for training, demonstrations, and advanced RDF practice.



Comments